Basys MX3

PIC32 Geliştirme Kartı

Digilent
Ürün Kodu: 72.01.02

 836,03

Fiyatı :

Share on facebook
Share on twitter
Share on linkedin
Share on whatsapp
Share on email

EasyMx PRO v7 for STM32 ARM

The Basys MX3 is a development platform for the Microchip PIC microcontroller (PIC32MX370). With an exhaustive set of Peripherals plus Pmod expansion headers, users can create a wide range of embedded systems applications. The board also provides an easy and cost-effective introduction to the PIC32 microcontroller and MPLAB® X Integrated Development Environment (IDE). A complete set of software libraries are included, allowing users to make simple function calls to all onboard peripherals, greatly simplifying the development process. With the on-board debug headers and USB programmer/debugger, users can debug their designs directly from MPLAB® X Integrated Development Environment , or scope digital and analog signals through Analog Discovery 2 or Digital Discovery. Accompanied by free and open-source coursework , including 7 in-depth teaching units and 15 complete labs, the Basys MX3 is also a versatile MCU trainer board ideal for teaching introductory embedded systems courses. It covers topics from toggling LED’s to motor control to digital signal processing. The coursework is designed for sophomore/junior level embedded systems courses.


FEATURES

●  Processor/IC: Microchip PIC32MX370F512L Microcontroller

MIPS32® M4K® core runs up to 96 MHz using onboard 8 MHz oscillator

●  512 KB of Program Flash Memory

●  12KB of Boot Flash Memory

●  128 KB of SRAM

●  Four Direct Memory Access (DMA) Modules

●  Two SPI, Two I²C, and Five UART serial interfaces

●  Parallel Master Port (PMP) for graphics interfaces

●  Five 16-bit Timers/Counters

●  Five Input Capture Modules

●  Five Output Compare Modules

●  85 I/O pins

●  54 pins support Peripheral Pin Select (PPS) for function remapping

Software

●  Designed for use with MPLAB X IDE

●  System Features

●  4 MB SPI Flash

●  Onboard USB UART (USB Micro cable required, NOT INCLUDED)

●  Supports baud rates up to 1.25 MBaud

●  Powered from USB or 5 V external power source

●  Standard barrel jack for 2.0 mm internal-diameter plug

●  No jumper select required

System Connectivity

●  USB-UART Bridge

●  Interaction and Sensory Devices

●  8 Slide Switches

●  5 Buttons

●  1 Reset Button

●  8 LEDs

●  1 RGB LED

●  Onboard 3-axis, 12-bit accelerometer

●  Programmable Motion Detection

●  I2C Interface with Programmable Interrupt

●  Onboard FIR-compatible IrDA Module

●  Built-in Remote Control Transmission Function

●  Supports speeds up to 4 Mbps

●  Onboard Audio Input and Output

●  MEMS Microphone with Adjustable Gain

●  Thumbwheel potentiometer for adjusting mic volume

●  PWM driven mono audio output with onboard speaker

●  Thumbwheel potentiometer for adjusting speaker volume

●  3.5 mm jack for line out connection to external amplifier/speaker system

●  Onboard Displays

●  2×16 LCD Character Display with LED backlight

●  4-Digit Seven Segment Display with red LEDs

Motor Control

●  Onboard Dual H-Bridge Motor Driver

●  Supports up to two 1.5 A Brushed DC Motors or one stepper motor

●  Supports motor voltages up to 11 V

●  Terminal block provides easy connection to motors

●  2 Servo Connectors

●  Analog Input Control (AIC)

●  Thumbwheel potentiometer for varying analog input between 0 to 3.3 V

●  Two wire loops for ground and AIC

●  Expansion Connectors

●  Two 2×6 Pmod host ports

●  SPI, UART, GPIO, PWM, analog in

●  Terminal block for two DC motors or one stepper motor

●  Two R/C servo connectors

●  One I²C connector

●  Debugging

●  On-board 30-pin Analog Discovery 2 connector

●  On-board USB programmer/debugger Motor

●  Program/debug the PIC32MX370 directly from MPLAB / MPLABX

Support

●  7 free and open-source teaching units complete with 15 labs

●  Enough content to support one to two semesters of undergraduate embedded systems coursewors

Paket içeriği :
Basys MX3 Kartı

(Mikro USB Kablo ayrıca alınmalıdır)